What is the significance of PCB impedance for PCB circuit boards, and why do PCB circuit boards need impedance? This article first introduces what impedance and the type of impedance are, secondly introduces why the PCB circuit board needs to be impedance, and finally expounds the meaning of impedance to the PCB circuit board. Follow us to learn more about it.
In circuits with resistance, inductance, and capacitance, the resistance to alternating current is called impedance. Impedance is usually represented by Z, which is a complex number. The real part is called resistance, and the imaginary part is called reactance. The blocking effect of capacitance on alternating current in the circuit is called capacitive reactance, and the blocking effect of inductance on alternating current in the circuit is called For inductive reactance, the blocking effect of capacitance and inductance on alternating current in the circuit is collectively called reactance. The unit of impedance is ohms.
1. Characteristic impedance
In electronic information products such as computers and wireless communications, the energy transmitted by the circuit board in the circuit is a square wave signal (called pulse) composed of voltage and time, and the resistance it encounters is called is the characteristic impedance.
2. Odd-mode impedance
The impedance Zoo of one line to the ground in the two lines, the impedance value of the two lines is the same.
3. Even mode impedance
The driving end inputs two identical signal waveforms with the same polarity, and the impedance Zcom when the two lines are connected together.
4. Differential impedance
The driving end inputs two identical signal waveforms with opposite polarities, which are respectively transmitted by two differential lines, and the two differential signals are subtracted at the receiving end. The differential impedance is the impedance Zdiff between the two wires.
5. Common mode impedance
The impedance Zoe of one line to the ground in the two lines, the impedance value of the two lines is the same, usually larger than the odd mode impedance.
The impedance of the pcb circuit board refers to the parameters of resistance and reactance, which hinder the alternating current. In the production of pcb circuit boards, impedance processing is essential. The reasons are as follows:
1. The PCB circuit board (the bottom of the board) should be considered for the installation of electronic components, and the conductivity and signal transmission performance should be considered after plugging. Therefore, the lower the impedance, the better, and the resistivity should be lower than 1&TImes; 10-6 or less.
2. During the production process, the PCB circuit board has to go through the process of copper sinking, electroplating tin (or electroless plating, or thermal spray tin), connector soldering and other processes, and the materials used in these links must ensure that the resistivity is low to ensure that The overall impedance of the circuit board is low to meet the product quality requirements and can operate normally.
3. The tinning of the PCB circuit board is the most prone to problems in the production of the entire circuit board, and it is the key link that affects the impedance. The biggest defect of electroless tin plating layer is easy discoloration (easy to oxidize or deliquescence) and poor solderability, which will make the circuit board difficult to solder, and the impedance will be too high, resulting in poor electrical conductivity or unstable performance of the whole board.
4. There will be various signal transmissions in the conductors in the PCB circuit board. In order to improve the transmission rate, the frequency must be increased. If the line itself is different due to factors such as etching, stack thickness, and wire width, the impedance value will change. , so that the signal is distorted and the performance of the circuit board is degraded, so it is necessary to control the impedance value within a certain range.
For the electronics industry, according to industry surveys, the most fatal weakness of electroless tin plating is easy discoloration (both easy to oxidize or deliquescence), poor solderability, which leads to difficult soldering, and high impedance, which leads to poor electrical conductivity or unstable performance of the entire board. , Easy to grow tin whiskers, resulting in a short circuit of the PCB circuit and even burn or fire.
It is reported that the first domestic research on electroless tin plating was Kunming University of Science and Technology in the early 1990s, followed by Guangzhou Tongqian Chemical Industry (enterprise) in the late 1990s. Up to now, for 10 years, the industry has recognized the two institutions as doing get the best. Among them, according to our contact screening investigation, experimental observation and long-term endurance test of many enterprises, it is confirmed that the tin plating layer of Tongqian Chemical Industry is a pure tin layer with low resistivity, and the quality of electrical conductivity and brazing can be guaranteed to a high level. No wonder they dare to guarantee to the outside world that the coating can keep no discoloration, no blistering, no peeling, and no tin whiskers for one year without any sealing and anti-discoloration agent protection.
Later, when the entire social production industry developed to a certain level, many later participants tended to copy each other. In fact, a considerable number of enterprises themselves did not have the ability to develop or initiate innovation. Therefore, many products and their users' electronic products (circuit boards) were created. The main reason for the poor performance is the impedance problem, because when the unqualified electroless tin plating technology is in use, the tin plated on the PCB is actually It is not really pure tin (or pure metal), but a compound of tin (that is, it is not a metal at all, but a metal compound, oxide or halide, more directly a non-metallic substance) or tin A mixture of compound and tin metal element, but it is difficult to detect with the naked eye alone.
Because the main circuit of the PCB circuit board is copper foil, the tinned layer is on the solder joints of the copper foil, and the electronic components are welded on the tinned layer by solder paste (or solder wire). In fact, the solder paste is melting. The state soldered between the electronic components and the tin coating is metal tin (that is, a metal element with good electrical conductivity), so it can be briefly pointed out that the electronic components are connected to the copper foil at the bottom of the circuit board through the tin coating, so the tin coating The purity of the instrument and its impedance are the key; and, before connecting the electronic components, when we directly use the instrument to detect the impedance, in fact, the two ends of the instrument probe (or test lead) are also contacted by the copper foil on the bottom of the PCB. The tin plating on the surface is connected with the copper foil at the bottom of the PCB to connect the current. Therefore, the tin plating layer is the key, the key to affecting the impedance and the key to the performance of the entire circuit board, and the key that is easy to be ignored.
As we all know, except for the metal element, its compounds are all bad conductors of electricity or even non-conductive (also, this is also the key to the existence of distribution capacity or transmission capacity in the circuit), so there is this kind of conductive but not conductive in the tin plating layer. When the compound or mixture of tin is present, the resistivity of the ready-made or the electrolytic reaction of future oxidation and moisture and its corresponding impedance are quite high (enough to affect the level or signal transmission in digital circuits,) and Their characteristic impedances are also inconsistent. So it will affect the performance of the circuit board and the whole machine.
Therefore, as far as the current social production phenomenon is concerned, the material and properties of the coating on the bottom of the circuit board are the main and most direct reasons that affect the characteristic impedance of the entire circuit board, but also because of its ability to age with the coating layer and moisture electrolysis The variability of the impedance, so the worrying effect of its impedance becomes more insidious and variable. The main reasons for its concealment are: firstly, it cannot be seen by the naked eye (including its changes), and secondly, it cannot be measured constantly, because its There is variability with time and environmental humidity, so it is always easy to be ignored.
English
Chinese